Project

General

Profile

Problem finding settings for single LNB Multiswitch

Added by Tom Muke almost 2 years ago

Hi at all,
i got a little trouble finding the right Adapter settings for tvheadend to use with my Sat-setup:
The Sat-signal is shared via an Astro EcoSwitch (image attached). I already tried different setups in tvheadend without any success.
Always getting the same Message in log:

2022-12-28 08:20:58.542 mpegts: 11494H in Sat-TV - tuning on Montage Technology M88RS6000 #0 : DVB-S #0

2022-12-28 08:20:58.582 epggrab: 11494H in Sat-TV - registering mux for OTA EPG

2022-12-28 08:20:58.582 subscription: 0011: "scan" subscribing to mux "11494H", weight: 5, adapter: "Montage Technology M88RS6000 #0 : DVB-S #0", network: "Sat-TV", service: "Raw PID Subscription"

2022-12-28 08:21:08.550 mpegts: 11494H in Sat-TV - scan no data, failed

2022-12-28 08:21:08.550 subscription: 0011: "scan" unsubscribing

Setup:
Ubuntu 22.04 LXC Container on Proxmox
Hauppauge Win-TV Starburst2 PCI Card
Sattelite: Astra 19.2E

Hope someone can help me;)


Replies (10)

RE: Problem finding settings for single LNB Multiswitch - Added by Tom Muke almost 2 years ago

Thank for your quick reply, but i think that's not the problem:
Tried with fiollowing settings (image).
Result:
2022-12-28 09:40:35.934 mpegts: 11493.75H in Sat-TV - tuning on Montage Technology M88RS6000 #0 : DVB-S #0

2022-12-28 09:40:35.936 epggrab: 11493.75H in Sat-TV - registering mux for OTA EPG

2022-12-28 09:40:35.937 subscription: 0017: "scan" subscribing to mux "11493.75H", weight: 5, adapter: "Montage Technology M88RS6000 #0 : DVB-S #0", network: "Sat-TV", service: "Raw PID Subscription"

2022-12-28 09:40:45.934 mpegts: 11493.75H in Sat-TV - scan no data, failed

2022-12-28 09:40:45.934 subscription: 0017: "scan" unsubscribing

RE: Problem finding settings for single LNB Multiswitch - Added by Ron L almost 2 years ago

You have a quad output Universal LNBF with 4 coax lines going to the multiswitch?

RE: Problem finding settings for single LNB Multiswitch - Added by Tom Muke almost 2 years ago

Ron L wrote:

You have a quad output Universal LNBF with 4 coax lines going to the multiswitch?

yes, it's the one on the attached image.

RE: Problem finding settings for single LNB Multiswitch - Added by Tom Muke almost 2 years ago

saen acro wrote:

You use not existing frequency.

I think it exists:

https://www.daserste.de/specials/service/frequenzen-100.html

Am I wrong?

RE: Problem finding settings for single LNB Multiswitch - Added by saen acro almost 2 years ago

Astra 19E support NIT find working frequency rest will appear automatically.

I'm not scan/update from 2 years 19E, dish pointed elsewhere.

RE: Problem finding settings for single LNB Multiswitch - Added by Ron L almost 2 years ago

Tom Muke wrote:

Ron L wrote:

You have a quad output Universal LNBF with 4 coax lines going to the multiswitch?

yes, it's the one on the attached image.

Actually I was asking about your LNBF. This is another picture of your multiswitch. Assuming you have a quad universal LNBF connected with 4 coax lines to the 4 input ports on this multiswitch as far as I know Universal LNBF is the correct setting. The rest of your config appears OK. 11494000 should be accurate enough to tune. According to Lyngsat that is ARD Digital. I can't receive that satellite so I can't confirm the signal exists.

Can other tuners get this signal?

RE: Problem finding settings for single LNB Multiswitch - Added by Tom Muke almost 2 years ago

Sorry! Yes there are four coax lines from the LNB to the four Inputs of the multiswitch.
I have no problem finding the signal on three TVs and one receiver... So at the moment I think, the tuner on the PCI Card might be defect...
Thanks for your help!

RE: Problem finding settings for single LNB Multiswitch - Added by saen acro almost 2 years ago

Is cables correctly connected VL VH HL HH?

If use stock driver this is also expected
https://github.com/b-rad-NDi/Ubuntu-media-tree-kernel-builder

    (1-10/10)