TBS6902 - no input source available
Added by KenyBDG K. over 3 years ago
From few years I'm using TBS6902 with TVH 4.2.8-34 and everything work well.
Because I can watch only two channels simultaneously I decided to buy same TBS6902.
After installation the card has been detected by TVH without any issue, but when unfortunately I cannot watch anything using this new card.
I've noticed on TVH log,
2021-03-09 20:02:32.973 subscription: 00C0: No input source available for subscription"
Maybe card is broken, but before I send back to seller, I'd like to be sure that everything is ok on my side.
I've been testing also just one card to be sure that power supply is ok, but there is no matter, if I use one or both card.
Of course old one TBS6902 work fine.
Replies (19)
RE: TBS6902 - no input source available - Added by Ron L over 3 years ago
The red dots on the last two adapters indicate that they have not been enabled in the configuration.
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
Yes you are right but I disabled this adapters because they caused problems
RE: TBS6902 - no input source available - Added by Ron L over 3 years ago
If you remove the old card and use only the new card it does not work?
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
Yes, doesn't work.....I used also same PCI-E port.... no succeed
RE: TBS6902 - no input source available - Added by Ron L over 3 years ago
That sounds like a defective device then.
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
It seems that you are right..... I was hoping I forgot to configure something..
RE: TBS6902 - no input source available - Added by Ron L over 3 years ago
As long as the network is assigned to the device it should be used. Some of these dual tuner devices needed some extra config with the linked input setting but if it's working with the old card then your settings must be correct.
RE: TBS6902 - no input source available - Added by saen acro over 3 years ago
Reinstall TBS driver
Test is it work with some "elec" distro on usb drive.
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
I've reinstalled drivers couple of time, no succeed.
But I'll try to install some "elec" distro, I'm using TVH on Proxmox, so it's shouldn't any problem with installation "elec" distro (I hope so)
RE: TBS6902 - no input source available - Added by Ron L over 3 years ago
They are identical cards. If one works then you pull it out, install the other and it doesn't work then that isn't a driver issue.
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
The seller replaced the card with a new one, but no improvement, issue is the same. I've no idea what is the root cause...
RE: TBS6902 - no input source available - Added by saen acro over 3 years ago
What hardware you use?
What OS
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
Mainboard GA-B85M-D3H
Processor i7 4790
Ram - 16GB
OS - Debian (Proxmox VE) Tvhedaend is installed on container LXC
RE: TBS6902 - no input source available - Added by Ron L over 3 years ago
Have they changed out any of the chips on the newer cards?
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
It seems that both card have the same chipset
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
I've noticed sth suspcious
root@pve:~/media_build# lspci -vvv | grep 6902 Subsystem: Device 6902:0002 pcilib: sysfs_read_vpd: read failed: Input/output error Subsystem: Device 6902:0003
RE: TBS6902 - no input source available - Added by saen acro over 3 years ago
Install LibreElec on USB Drive and test, isolating virtualization.
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
I've been talking with TBS support.
TBS6902 has a new SoC which need new drivers, unfortnately they need some time to prepare drivers for this SoC, they will probably deliver it next Monday...... (I hope)
RE: TBS6902 - no input source available - Added by KenyBDG K. over 3 years ago
Update from TBS
Hi It is the HV voltage control reversal problem , when you set "H", the voltage is 13V, set "v" ,the voltage is 18V. so you just need setting the opposite voltage ,you will get the channel. later i will fixed it. Thanks for your feedback. Best Regards