Project

General

Profile

Forums » General »

[Gelöst]TVH Muxes scan Fail on ARMBIAN

Added by Thomas xyz almost 6 years ago

Hi,
i use TVH with a Haupage WinTV Dual DVB-C Stick on a Wetek Play 2 with CoreElec and it run's.

Now i wan't to setup the Stick on my Cubitruck with Armbian Linux cubietruck 4.18.8-sunxi, the WinTVDual is in TVH and booth Tuners activate, but by scanning the Network, i see 41 Muxes, but when i scan them, all Muxes Fail, what can be the Problem? In the Log i see

2018-11-26 06:34:12.556 mpegts: 626MHz in Kevag - scan no data, failed
2018-11-26 06:34:12.556 subscription: 00CE: "scan" unsubscribing
2018-11-26 06:34:12.556 mpegts: 330MHz in Kevag - tuning on Kevag
2018-11-26 06:34:12.556 epggrab: 330MHz in Kevag - registering mux for OTA EPG
2018-11-26 06:34:12.562 subscription: 00D1: "scan" subscribing to mux "330MHz", weight: 6, adapter: "Kevag", network: "Kevag", service: "Raw PID Subscription" 
2018-11-26 06:34:17.555 mpegts: 330MHz in Kevag - scan no data, failed
2018-11-26 06:34:17.555 subscription: 00D1: "scan" unsubscribing

The Same Stick with the Same connection run's on the WP2 fine......

Thank you


Replies (7)

RE: TVH Muxes scan Fail on ARMBIAN - Added by Mark Clarkstone almost 6 years ago

What does, dmesg say? Can you use w_scan OK?

RE: TVH Muxes scan Fail on ARMBIAN - Added by Thomas xyz almost 6 years ago

Hi, dmesg says

[81353.318475] usb 1-1.2: New USB device found, idVendor=2040, idProduct=0265, bcdDevice= 1.00
[81353.318490] usb 1-1.2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[81353.318496] usb 1-1.2: Product: dualHD
[81353.318502] usb 1-1.2: Manufacturer: HCW
[81353.318508] usb 1-1.2: SerialNumber: 0011569275
[81353.356377] em28xx 1-1.2:1.0: New device HCW dualHD @ 480 Mbps (2040:0265, interface 0, class 0)
[81353.356395] em28xx 1-1.2:1.0: DVB interface 0 found: isoc
[81353.426861] em28xx 1-1.2:1.0: chip ID is em28174
[81354.735086] em28xx 1-1.2:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x63e2c3c8
[81354.735110] em28xx 1-1.2:1.0: EEPROM info:
[81354.735128] em28xx 1-1.2:1.0:        microcode start address = 0x0004, boot configuration = 0x01
[81354.743333] em28xx 1-1.2:1.0:        AC97 audio (5 sample rates)
[81354.743346] em28xx 1-1.2:1.0:        500mA max power
[81354.743357] em28xx 1-1.2:1.0:        Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
[81354.806688] em28xx 1-1.2:1.0: Identified as Hauppauge WinTV-dualHD DVB (card=99)
[81354.811650] tveeprom: Hauppauge model 204109, rev B3I6, serial# 11569275
[81354.811662] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
[81354.811670] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[81354.811676] tveeprom: audio processor is None (idx 0)
[81354.811681] tveeprom: has no radio, has IR receiver, has no IR transmitter
[81354.811698] em28xx 1-1.2:1.0: dvb set to isoc mode.
[81354.947290] em28xx 1-1.2:1.0: chip ID is em28174
[81356.255217] em28xx 1-1.2:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x63e2c3c8
[81356.255230] em28xx 1-1.2:1.0: EEPROM info:
[81356.255237] em28xx 1-1.2:1.0:        microcode start address = 0x0004, boot configuration = 0x01
[81356.263574] em28xx 1-1.2:1.0:        AC97 audio (5 sample rates)
[81356.263587] em28xx 1-1.2:1.0:        500mA max power
[81356.263597] em28xx 1-1.2:1.0:        Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
[81356.326690] em28xx 1-1.2:1.0: Identified as Hauppauge WinTV-dualHD DVB (card=99)
[81356.331638] tveeprom: Hauppauge model 204109, rev B3I6, serial# 11569275
[81356.331648] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
[81356.331656] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[81356.331661] tveeprom: audio processor is None (idx 0)
[81356.331666] tveeprom: has no radio, has IR receiver, has no IR transmitter
[81356.331684] em28xx 1-1.2:1.0: dvb ts2 set to isoc mode.
[81356.532991] usbcore: registered new interface driver em28xx
[81356.544771] em28xx 1-1.2:1.0: Binding DVB extension
[81356.572493] i2c i2c-5: Added multiplexed i2c bus 8
[81356.572512] si2168 5-0064: Silicon Labs Si2168-B40 successfully identified
[81356.572519] si2168 5-0064: firmware version: B 4.0.2
[81356.588602] si2157 8-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
[81356.588748] dvbdev: DVB: registering new adapter (1-1.2:1.0)
[81356.588768] em28xx 1-1.2:1.0: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
[81356.591551] em28xx 1-1.2:1.0: DVB extension successfully initialized
[81356.591574] em28xx 1-1.2:1.0: Binding DVB extension
[81356.607473] i2c i2c-7: Added multiplexed i2c bus 9
[81356.607491] si2168 7-0067: Silicon Labs Si2168-B40 successfully identified
[81356.607499] si2168 7-0067: firmware version: B 4.0.2
[81356.621601] si2157 9-0063: Silicon Labs Si2147/2148/2157/2158 successfully attached
[81356.621735] dvbdev: DVB: registering new adapter (1-1.2:1.0)
[81356.621753] em28xx 1-1.2:1.0: DVB: registering adapter 1 frontend 0 (Silicon Labs Si2168)...
[81356.624109] em28xx 1-1.2:1.0: DVB extension successfully initialized
[81356.624126] em28xx: Registered (Em28xx dvb Extension) extension
[81356.643083] em28xx 1-1.2:1.0: Registering input extension
[81356.698579] si2168 5-0064: Direct firmware load for dvb-demod-si2168-b40-01.fw failed with error -2
[81356.698594] si2168 5-0064: Falling back to syfs fallback for: dvb-demod-si2168-b40-01.fw
[81356.702163] si2168 5-0064: Direct firmware load for dvb-demod-si2168-02.fw failed with error -2
[81356.702176] si2168 5-0064: Falling back to syfs fallback for: dvb-demod-si2168-02.fw
[81356.706845] Registered IR keymap rc-hauppauge
[81356.707962] rc rc1: 1-1.2:1.0 IR as /devices/platform/soc@1c00000/1c14000.usb/usb1/1-1/1-1.2/1-1.2:1.0/rc/rc1
[81356.708215] input: 1-1.2:1.0 IR as /devices/platform/soc@1c00000/1c14000.usb/usb1/1-1/1-1.2/1-1.2:1.0/rc/rc1/input2
[81356.709062] rc rc1: lirc_dev: driver em28xx registered at minor = 1, scancode receiver, no transmitter
[81356.709078] em28xx 1-1.2:1.0: Input extension successfully initialized
[81356.709090] em28xx 1-1.2:1.0: Remote control support is not available for this card.
[81356.709096] em28xx: Registered (Em28xx Input Extension) extension
[81356.727902] si2168 5-0064: firmware file 'dvb-demod-si2168-02.fw' not found
[81356.737496] si2157 8-0060: found a 'Silicon Labs Si2157-A30'
[81356.788325] si2157 8-0060: firmware version: 3.0.5
[81356.788408] em28xx 1-1.2:1.0: DVB: adapter 0 frontend 0 frequency 0 out of range (42000000..870000000)
[81356.798387] si2168 5-0064: Direct firmware load for dvb-demod-si2168-02.fw failed with error -2
[81356.798402] si2168 5-0064: Falling back to syfs fallback for: dvb-demod-si2168-02.fw
[81356.801075] si2168 5-0064: Direct firmware load for dvb-demod-si2168-02.fw failed with error -2
[81356.801090] si2168 5-0064: Falling back to syfs fallback for: dvb-demod-si2168-02.fw
[81356.804282] si2168 7-0067: Direct firmware load for dvb-demod-si2168-b40-01.fw failed with error -2
[81356.804295] si2168 7-0067: Falling back to syfs fallback for: dvb-demod-si2168-b40-01.fw
[81356.807863] si2168 5-0064: firmware file 'dvb-demod-si2168-02.fw' not found
[81356.807959] si2168 7-0067: firmware file 'dvb-demod-si2168-02.fw' not found
[81356.817534] si2157 9-0063: found a 'Silicon Labs Si2157-A30'
[81356.868701] si2157 9-0063: firmware version: 3.0.5
[81356.868791] em28xx 1-1.2:1.0: DVB: adapter 1 frontend 0 frequency 0 out of range (42000000..870000000)
[81356.882150] si2168 7-0067: Direct firmware load for dvb-demod-si2168-02.fw failed with error -2
[81356.882164] si2168 7-0067: Falling back to syfs fallback for: dvb-demod-si2168-02.fw
[81356.890301] si2168 7-0067: Direct firmware load for dvb-demod-si2168-02.fw failed with error -2
[81356.890317] si2168 7-0067: Falling back to syfs fallback for: dvb-demod-si2168-02.fw
[81356.894548] si2168 7-0067: firmware file 'dvb-demod-si2168-02.fw' not found

w_scan says this

w_scan -f c -c DE
w_scan -f c -c DE
w_scan version 20161022 (compiled for DVB API 5.10)
using settings for GERMANY
DVB cable
DVB-C
scan type CABLE, channellist 7
output format vdr-2.0
WARNING: unknown codepage 'de_DE', using default 'UTF-8'
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
main:3916: FATAL: ***** NO USEABLE CABLE CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

I think since kernel 4.17 shout the WinTVDual is integrated!?

RE: TVH Muxes scan Fail on ARMBIAN - Added by Mark Clarkstone almost 6 years ago

You're missing firmware, grab dvb-demod-si2168-b40-01.fw and replug/reboot, then try again.

RE: TVH Muxes scan Fail on ARMBIAN - Added by Thomas xyz almost 6 years ago

Can you please explain to me more exactly what I have to do for it?
Thank you

RE: TVH Muxes scan Fail on ARMBIAN - Added by Mark Clarkstone almost 6 years ago 

sudo -s
cd /lib/firmware
wget http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/4.0.25/dvb-demod-si2168-b40-01.fw
reboot

RE: TVH Muxes scan Fail on ARMBIAN - Added by Thomas xyz almost 6 years ago

Thank you,
now dmesg shows this

 15.374797] em28xx 1-1.2:1.0: New device HCW dualHD @ 480 Mbps (2040:0265, interface 0, class 0)
[   15.374815] em28xx 1-1.2:1.0: DVB interface 0 found: isoc
[   15.403395] cdc_acm 4-1:1.0: ttyACM0: USB ACM device
[   15.404467] usbcore: registered new interface driver cdc_acm
[   15.404475] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   15.452945] em28xx 1-1.2:1.0: chip ID is em28174
[   15.717663] zram0: detected capacity change from 0 to 52428800
[   17.119586] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard
[   17.301168] em28xx 1-1.2:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x63e2c3c8
[   17.301181] em28xx 1-1.2:1.0: EEPROM info:
[   17.301189] em28xx 1-1.2:1.0:        microcode start address = 0x0004, boot configuration = 0x01
[   17.309302] em28xx 1-1.2:1.0:        AC97 audio (5 sample rates)
[   17.309316] em28xx 1-1.2:1.0:        500mA max power
[   17.309327] em28xx 1-1.2:1.0:        Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
[   17.372766] em28xx 1-1.2:1.0: Identified as Hauppauge WinTV-dualHD DVB (card=99)
[   17.381250] tveeprom: Hauppauge model 204109, rev B3I6, serial# 11569275
[   17.381285] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
[   17.381294] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[   17.381299] tveeprom: audio processor is None (idx 0)
[   17.381304] tveeprom: has no radio, has IR receiver, has no IR transmitter
[   17.381322] em28xx 1-1.2:1.0: dvb set to isoc mode.
[   17.443274] em28xx 1-1.2:1.0: chip ID is em28174
[   18.750950] em28xx 1-1.2:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x63e2c3c8
[   18.750969] em28xx 1-1.2:1.0: EEPROM info:
[   18.750982] em28xx 1-1.2:1.0:        microcode start address = 0x0004, boot configuration = 0x01
[   18.766707] em28xx 1-1.2:1.0:        AC97 audio (5 sample rates)
[   18.766731] em28xx 1-1.2:1.0:        500mA max power
[   18.766753] em28xx 1-1.2:1.0:        Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
[   18.832857] em28xx 1-1.2:1.0: Identified as Hauppauge WinTV-dualHD DVB (card=99)
[   18.851979] tveeprom: Hauppauge model 204109, rev B3I6, serial# 11569275
[   18.851996] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
[   18.852003] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[   18.852008] tveeprom: audio processor is None (idx 0)
[   18.852013] tveeprom: has no radio, has IR receiver, has no IR transmitter
[   18.852035] em28xx 1-1.2:1.0: dvb ts2 set to isoc mode.
[   19.074501] usbcore: registered new interface driver em28xx
[   19.092001] em28xx 1-1.2:1.0: Binding DVB extension
[   19.152614] i2c i2c-5: Added multiplexed i2c bus 8
[   19.152643] si2168 5-0064: Silicon Labs Si2168-B40 successfully identified
[   19.152744] si2168 5-0064: firmware version: B 4.0.2
[   19.190286] si2157 8-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
[   19.190402] dvbdev: DVB: registering new adapter (1-1.2:1.0)
[   19.190418] em28xx 1-1.2:1.0: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
[   19.200304] em28xx 1-1.2:1.0: DVB extension successfully initialized
[   19.200323] em28xx 1-1.2:1.0: Binding DVB extension
[   19.229107] i2c i2c-7: Added multiplexed i2c bus 9
[   19.229128] si2168 7-0067: Silicon Labs Si2168-B40 successfully identified
[   19.229136] si2168 7-0067: firmware version: B 4.0.2
[   19.241657] si2157 9-0063: Silicon Labs Si2147/2148/2157/2158 successfully attached
[   19.241776] dvbdev: DVB: registering new adapter (1-1.2:1.0)
[   19.241795] em28xx 1-1.2:1.0: DVB: registering adapter 1 frontend 0 (Silicon Labs Si2168)...
[   19.248176] em28xx 1-1.2:1.0: DVB extension successfully initialized
[   19.248193] em28xx: Registered (Em28xx dvb Extension) extension
[   19.314631] em28xx 1-1.2:1.0: Registering input extension
[   19.432830] Registered IR keymap rc-hauppauge
[   19.434292] rc rc1: 1-1.2:1.0 IR as /devices/platform/soc@1c00000/1c14000.usb/usb1/1-1/1-1.2/1-1.2:1.0/rc/rc1
[   19.434642] input: 1-1.2:1.0 IR as /devices/platform/soc@1c00000/1c14000.usb/usb1/1-1/1-1.2/1-1.2:1.0/rc/rc1/input2
[   19.435604] rc rc1: lirc_dev: driver em28xx registered at minor = 1, scancode receiver, no transmitter
[   19.435624] em28xx 1-1.2:1.0: Input extension successfully initialized
[   19.435641] em28xx 1-1.2:1.0: Remote control support is not available for this card.
[   19.435650] em28xx: Registered (Em28xx Input Extension) extension
[   33.985764] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[   33.989837] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features support found
[   33.989853] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum Offload disabled
[   33.989872] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management Counters available
[   33.989882] sun7i-dwmac 1c50000.ethernet eth0: PTP not supported by HW
[   33.990631] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   35.146962] sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   35.147021] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   49.371565] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   49.462398] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   54.058333] si2168 7-0067: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
[   54.162753] brcmfmac: brcmf_p2p_create_p2pdev: timeout occurred
[   54.162777] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-5
[   54.240463] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   55.052957] em28xx 1-1.2:1.0: write to i2c device at 0xce failed with unknown error (status=12)
[   55.052979] si2168 7-0067: firmware download failed -5
[   55.087347] si2157 9-0063: found a 'Silicon Labs Si2157-A30'
[   55.142832] si2157 9-0063: firmware version: 3.0.5
[   55.142956] em28xx 1-1.2:1.0: DVB: adapter 1 frontend 0 frequency 0 out of range (42000000..870000000)
[   55.221098] si2168 7-0067: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
[   55.221225] si2168 5-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
[   56.653209] si2168 7-0067: firmware version: B 4.0.25
[   56.656059] si2168 5-0064: firmware version: B 4.0.25
[   56.671176] si2157 8-0060: found a 'Silicon Labs Si2157-A30'
[   56.723289] si2157 8-0060: firmware version: 3.0.5
[   56.723391] em28xx 1-1.2:1.0: DVB: adapter 0 frontend 0 frequency 0 out of range (42000000..870000000)
[   56.749592] si2168 5-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
[   58.010097] si2168 5-0064: firmware version: B 4.0.25

It still gives a error message:
<pre>
[   54.058333] si2168 7-0067: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
[   54.162753] brcmfmac: brcmf_p2p_create_p2pdev: timeout occurred
[   54.162777] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-5
[   54.240463] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   55.052957] em28xx 1-1.2:1.0: write to i2c device at 0xce failed with unknown error (status=12)
[   55.052979] si2168 7-0067: firmware download failed -5
</pre>

but w-scan runs fine and TVH now find services.

Thank you for your help
    (1-7/7)