Forums » Tutorial and setups »
"No input source available" with minisatip SAT-IP Serve
Added by Udo Giacomozzi over 4 years ago
I've got an essentially working Tvheadend setup for 2-3 years, but now want to swap the Triax TSS 400 Satip Server in favor of a a Digibit R1 server and [custom firmware](https://github.com/jampy/satip-axe/tree/minisatip-socket-patch), so that the stream is served by [minisatip](https://github.com/catalinii/minisatip) (at IP 10.0.1.25).
The SAT-IP Server works fine using "SatIP DVBViewer" windows software, however TvHeadend fails to accept the Digibit as input source.
2020-08-10 09:53:44.983 [ TRACE] subscription: 0006: find service for SUPER RTL weight 100 2020-08-10 09:53:44.984 [ NOTICE] subscription: 0006: No input source available for subscription "10.0.1.105 [ | Kodi Media Center ]" to channel "SUPER RTL"
See debug output at https://pastebin.com/mVksd3f4
Config details:
What am I missing??
Some additional setup details:- Tvheadend 4.2.1 on Synology NAS in Docker container
- I've got a custom-built triple DVB-T server on Raspberry Pi (also minisatip) working fine with Tvheadend (IP 10.0.1.18)
- Currently (for testing) only one of the four tuners of the Digitbit R1 receiver is connected to a port of the multiplexer of the satellite dish
- I've set different "device IDs" for the minisatip servers, but Tvheadend only shows the number for the (working) DVB-T server, not for the DVB-S server (see screenshot)
Replies (8)
RE: "No input source available" with minisatip SAT-IP Serve - Added by saen acro over 4 years ago
Remove extra "Satellite positions" if not used "1" is enough
Do you create network to attach to inputs?
Is network contain real transponder parameters?
RE: "No input source available" with minisatip SAT-IP Serve - Added by Udo Giacomozzi over 4 years ago
Thanks for your reply.
I do have networks, yes:
Note that when I additionally activate the (still powered on) Triax server using options `--satip_xml http://10.0.1.22:80/rootDescr --satip_xml http://10.0.1.18:9090/desc.xml --satip_xml http://10.0.1.25:8080/desc.xml --trace satip,service,mpegts,subscription -d -S` then I can watch programs just fine (Tvheadend always uses the Triax server then).
If you're interested in screenshots with all three servers active (Triax TS 400, Digibit R1 via minisatip, DVB-T via minisatip) have a look here:
https://i.imgur.com/gxAfW3P.png
https://i.imgur.com/tXdGlzy.png
https://i.imgur.com/ze2Zgxq.png
Both the Triax and Digibit receivers are connected to the same Switch, although the Digibit only has one cable connected, currently.
- reducing "satellite positions" did not help. What's that anyway?
- Do I explicitly need to link those network to the SAT-IP servers? I could not find any way to do so...
- whats the "SAT>IP source number"? could that be the problem?
RE: "No input source available" with minisatip SAT-IP Serve - Added by Udo Giacomozzi over 4 years ago
Oh my! I just realized that i also need to manually enable the "Position" and assign a network to it, like so:
So, for a SAT-IP Server to work, one has to...
- manually / explicitly enable each single tuner
- manually / explicitly enable each single position
- manually / explicitly assign each position to a network
You see, I did that once for the Triax, but this irritates me again and again (and I looked at those "Parameters" panels for hours...).
Ok, so it seems to work now. :-)
As a last question, could you please explain to me what those "positions" mean?
RE: "No input source available" with minisatip SAT-IP Serve - Added by saen acro over 4 years ago
See Muxes tab, and add there some real transponder to your network "DVB-S Network"
https://en.kingofsat.net/pos-19.2E.php
RE: "No input source available" with minisatip SAT-IP Serve - Added by Udo Giacomozzi over 4 years ago
Excuse me, what do you mean? I have quite a lot of muxes there.
As said in my earlier post, the setup is working now.
I was just wondering, what's the exact meaning of those tuner "positions" that default to 4.
RE: "No input source available" with minisatip SAT-IP Serve - Added by saen acro over 4 years ago
Diseq switch for 4 sat positions
RE: "No input source available" with minisatip SAT-IP Serve - Added by Udo Giacomozzi over 4 years ago
Well, the tuner is attached using 4 cables to a multiswitch.
Wouldn't setting 4 positions for each tuner give me more choices (ie. that should work IMHO), especially when streaming multiple channels at the same time?
RE: "No input source available" with minisatip SAT-IP Serve - Added by saen acro over 4 years ago
4 positions mean 19.2E 16E 23E 0.8W for example,
aka four satellite orbital positions
https://www.satlex.us/en/1participant-type_conf_1p_4s.html
https://www.satlex.us/en/4participants-type_conf_4p_4s_quad.html