Tvheadend

Hi

I have no problem using "HTS Tvheadend git-9d775da" and "OSCam cardserver v0.99.4svn, build #3146" with Omnikey Cardman 3021 or Adteknik USB Phoenix (http://www.adteknik.se/english/usbphoenix.htm).

From your oscam config file I think you are using the wrong caid for conax. Try to use 0B00 insted of 0B04.

Her are mine Oscam config files. I the oscam.server I have commented out use of the Omnikey Card Reader because for the moment I use the Adteknik USB Phoenix which I can overclock.

oscam.conf

[global]

[newcamd]
key = 0102030405060708091011121314
port = 15050@0B00:000000
keepalive = 1

[webif]
httpport = 8888
httpuser = dummy
httppwd = dummy
httpallowed = 127.0.0.1,10.0.0.0-10.0.0.255

oscam.server

#Omnikey Cardman 3021
#[reader]
#label = omnikey
#protocol = pcsc
#device = 0
#detect = CD
#group = 1
#emmcache = 1,3,2
#caid = 0B00

#AD-Teknik AB Multiprogrammer 3.6 USB
[reader]
label = adteknik
protocol = mp35
detect = CD
device = /dev/adph0
mhz = 600
group = 1
emmcache = 1,3,2
caid = 0B00

oscam.user

[account]
user = oscam
pwd = oscam
group = 1
au = adteknik

Hope it helps
Harald

Takk for svar. :-)

On startup oscam reports:
2011/08/24 11:05:49 9FD9660 r type: Conax, caid: 0B04, serial: 1326000140, hex serial: 4f09280c, card: v64

Both Oscam and newcs identifies caid as 0B04; and TvHeadend sends CAID 0B04 in the requests.
The weird part is that this used to work.

I've attached a .zip file with the last versions of my oscam config files, a -d 255 log of oscam startup+trying to decode 2 channels.
Also included is a 20s raw dump of an encrypted channel.

If anyone can see what's wrong I'd love to know what I've done wrong, and if possible what to do to fix it.

Hei igjen

I not an expert, but after checking the oscam.log I see error about writing ECM message to the cardreader through the PCSC daemon:

write to cardreader omnikey:
2011/08/24 11:16:00 9D9A660 DD CA 00 00 04
2011/08/24 11:16:00 9D9A660 r sending 5 bytes to PCSC : DD CA 00 00 04
2011/08/24 11:16:00 9D9A660 r received 6 bytes from PCSC with rv=0 : 31 02 00 00 90 12
2011/08/24 11:16:00 9D9A660 r PCSC doapi (0 ) (T=0), 6
2011/08/24 11:16:00 9D9A660 r Error processing ecm for caid 0B04, srvid 0000 (servicename: ) on reader omnikey.

This is maybe the same issues I have had when I tried to switch from Fedora 11 to Archlinux. On Fedora everything works with PCSC, ccid and vdr-sc, but on Archlinux nothing works. I used the same vdr-sc config on the archlinux box, but nothing works. After lots of investigation I suspected archlinux had a issue with PCSC and buggy vdr-sc code. So I bought a Adteknik usb-serial reader which didn't used PCSC and it worked.

Check on your Linuxbox if PCSC (PCSC-tools,pcsc-perl) and ccid are installed and have the same version as you had before you got this problems?

Harald

Hello again.
I have now set up another pc - ubuntu 11.04, with a smartmouse reader (no pcsc - direct access to ttyUSB0).
The infinity works, I can see my entitlements etc, but i still get the same error. (tvheadend (0B04&000000/0000/6F:484A): not found (0 ms) by reader-1 (of 1 avail 1)

Same config files except for oscam.server, which has mouse instead of pcsc.

I also tried newcs 1.67 rc1 with the infinity on this pc - same story. Newcs communicates with the card, can't descramble.

[ 22:04:49 ] [ Conax ] Viewing status: 0000
[ 22:04:49 ] [ 0B04 ] Card ECM took: 0s 273102us
[ 22:04:49 ] [ SID ] Updating SID 0000 for Reader 0 (Smartmouse) bad - SO is: 0
[ 22:04:49 ] [ ECM Cache ] Adding dynamic Cache entry at 3
[ 22:04:49 ] [ ECM Cache ] Hits 1 Total 4
[ 22:04:49 ] [ 0B04 ] Ecm Cache Add took: 0s 21us
[ 22:04:53 ] [ Newcamd:15051 ] ECM <- tvheadend
[ 22:04:53 ] [ SID ] Checking for SID 0000 for Reader 0 (Smartmouse) - SO is: 0
[ 22:04:53 ] [ Newcamd:15051 ] Accepted SID 0000 on Reader 0 (Smartmouse) from tvheadend
[ 22:04:53 ] [ ECM Added] [CAID 0000][Provider 00000000][SID 0000]
[ 22:04:53 ] [ ECM Cache ] Hits 2 Total 5 [CRC 52E69717] - returning -2
[ 22:04:53 ] [ 0B04 ] Ecm Cache Check took: 0s 14us [CRC 52e69717]
[ 22:04:53 ] [ ECM ] Cache Hit - Returning value -2

Even set up newcs on a windows-pc with omnikey reader - same problem here.

I'm starting to think they've done something to the stream.
Shouldn't tvHeadedend send the SID inn the request?

I'm really at a loss here.. any help would be appreciated!!