Tvheadend

Continuity errors indicate poor signal/reception errors. Did you verify if the issue is indeed a tvheadend issue and other Software is able to receive it properly?

Flole Systems wrote:

Continuity errors indicate poor signal/reception errors. Did you verify if the issue is indeed a tvheadend issue and other Software is able to receive it properly?

Thank you for quickly reply. We tested on servel different places with different equipments, which running tvh on Ubuntu or Libreelec. The signal is high enough like 13DB. Other channels on the same satellite are running perfect, zero error within 48 or 72 hours. ONlY the channels with SD format dvbsubs have the errors as mentioned above.
We also tested use the E2 boxs like VU+ as receiver and stream the channel into tvh with IPTV method, then the errors disappear. So we confirm the errors could be caused by a tvh bug.
I know EU have more PowerVU channels with dvbsubs and I googled found nothing with same problem. We think the reason is these errors ONLY appear with SD format subs on HD channels. On EU channels the subs almost HD format so the bug never shows up.

a z wrote:

We also tested use the E2 boxs like VU+ as receiver and stream the channel into tvh with IPTV method, then the errors disappear. So we confirm the errors could be caused by a tvh bug.

That sounds more like whatever hardware you are using isn't able to keep up with the bandwidth and when you use a different source that issue is gone. Please try to use a different Software (not tvheadend) to make sure those errors are indeed caused by tvheadend.

As far as I know there is no dvbviewer linux version, so you used a different driver and dvb stack by using a different operating system? Unfortunately that is not ruling out any issues in the driver and dvb stack, it only rules out a hardware defect and bad signal.

We also tried Astra , same hardware and same signal source. Same driver(tbs6904) on Ubuntu x86.

On the other hand, if the errors caused by a hardware defect or bad signal or some other reason. Could it be always same error logs which related to the DVBSUB section ? We tried times again with 2 months, the error log always the same , ONLY with DVBSUB section. Please check the picture I uploaded. Thank you.

We also tried Astra , same hardware and same signal source. Same driver(tbs6904) on Ubuntu x86.

Astra recorded ts files with no error.

There could be issues whenever a specific bandwidth is reached and the driver is unable to keep up with that bandwidth. This has been an issue before on different hardware. As continuity errors are indicating missed packets you need to figure out where they get lost.

Thank you for reply.

Now I tested again.

Test environment: one ubuntu x86 platform  + one tbs6904 dvb card  +  13db signal  +  tvh  +  VLC client

1, I switched tvh to Animax asia channel(5m-7m bitrate, 13DB signal),the dvbsub errors appears within 3 minutes and continuesly exist.

2, On same hardware and same ubuntu x86 with same dvb card driver, same satellite ,then I switched to Disney asia channel (6m-8m bitrate, 13DB signal)  ,play perfect with no error within 3 hours. Please note that the channel ONLY contain HD format dvbsubs.

3, On same hardware and same ubuntu x86 with same dvb card driver, I stoped tvh and start Astra , the Animax asia channel(which has many errors on first step) ,plays perfect with no error now.

The errors only occur on dvbsub section, we tested 20+ times within 2 months, always the same.  Like this: 

2020-04-30 12:38:21.768 TS: 91.5C/4120H/SET ONE (Mandarin): DVBSUB  #2304 Continuity counter error (total 1)
       2020-04-30 12:39:00.601 TS: 91.5C/4120H/SET ONE (Mandarin): DVBSUB  #2304 Continuity counter error (total 4)
       2020-04-30 12:43:20.306 TS: 91.5C/4120H/SET ONE (Mandarin): DVBSUB @ #2301 Continuity counter error (total 1)

I noted that ONLY channels contain SD format DVBSUB got the errors( Animax [email protected] ,  Sony [email protected] , BBC @91.5C ) . Those channels contain HD format DVBSUB (Disney asia channel  ) play perfect.  All these are PowerVU channels.

One more thing:

The errors only appear in Subscriptions -- Error .

In the stream page, there is zero error, including all 3 sections -- Ucorrected Blocks \ Transport Errors \ Continuity Errors. These 3 sections are all zero.

Flole Systems wrote:

Continuity errors indicate poor signal/reception errors. Did you verify if the issue is indeed a tvheadend issue and other Software is able to receive it properly?

That is usually said - but this is not always true.

Try the following:

Send a encrypted stream from an external tvh to tvh with cam.

Result:

- no errors while getting the encrypted stream from the reception card.

- cc error while handling the encyrpted stream

//Tom

Hello,

I tried TVH 4.2 on powervu channel(SONY ONE @ 91.5C), the subtitle has ZERO errors. But the TVH 4.3 got many errors in the same environment.

I tested again and again, the results always the same. The errors only show on Subscriptions. (TVH 4.3)

One of the differences between 4.2 and 4.3 is CW mode , maybe the codes related to the CW mode part has problem?

Please help me , thank you very much!