Project

General

Profile

Xbox One DVB-T/T2/C tuner

Added by Stephen Neal about 10 years ago

Hi all

This looks like it could be very good value if Open Source drivers appear for it : http://www.xbox.com/en-GB/xbox-one/accessories/digital-tv-tuner#fbid=1ui_UaaGUzy GBP£25/EUR€30 for a DVB-T/T2/C USB tuner for use with the Microsoft Xbox One (but like the Sony Play TV presumably usable on any PC platform if Linux drivers appear)


Replies (420)

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

@C vH
So I downloaded the New Image.
The Driver seems to be better because I have 2 Tuners now. DVB-C & DVB-T
I searched on DVB-C but again. No Services found.
Tried an other Stick and here I found all the Services.
When I trie to use booth the XBOX Stick didn't work. The Hauppauge work fine.

If you need something tell me I´ll post all u need.

RE: Xbox One DVB-T/T2/C tuner - Added by Stephen Neal over 7 years ago

Yep - I can't get the LibreElec buld from C vH to work with my XBox One tuner either - but my home compiled version of TV Headend only running on Jessie Lite with drivers compiled as above works fine. (Literally swapped the uSD cards out to check)

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

Smith Martin Neal,
on the Raspberry Pi3? Can you share it?

RE: Xbox One DVB-T/T2/C tuner - Added by Stephen Neal over 7 years ago

marco raap wrote:

Smith Martin Neal,
on the Raspberry Pi3? Can you share it?

I posted instructions earlier in this thread.

(This is purely for a TV Headend backend - not running LibreElec or Kodi front end)

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

Smith Martin Neal

did all you said and after 4 hours. Didn't work. Nice try.

So my last hope depends on C vH and his Image.
Sad why is it not possible to just use the driver.....

pi@raspberrypi:~/media_build $ sudo make dir DIR=../media
make -C linux/ dir DIR="../../media" 
make[1]: Entering directory '/home/pi/media_build/linux'
rm -rf drivers firmware include sound .patches_applied .linked_dir .git_log.md5 git_log kernel_version.h
../../media does not contain kernel sources
/bin/sh: 1: exit: Illegal number: -1
Makefile:128: recipe for target 'dir' failed
make[1]: *** [dir] Error 2
make[1]: Leaving directory '/home/pi/media_build/linux'
Makefile:32: recipe for target 'dir' failed
make: *** [dir] Error 2
pi@raspberrypi:~/media_build $ 

pi@raspberrypi:~ $ dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.35-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611) ) #1014 SMP Fri Jun 30 14:47:43 BST 2017
[    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: Raspberry Pi 3 Model B Rev 1.2
[    0.000000] cma: Reserved 8 MiB at 0x3a800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 241664
[    0.000000] free_area_init_node: node 0, pgdat 80c6ee40, node_mem_map b9faa000
[    0.000000]   Normal zone: 2124 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 241664 pages, LIFO batch:31
[    0.000000] percpu: Embedded 14 pages/cpu @b9f64000 s25600 r8192 d23552 u57344
[    0.000000] pcpu-alloc: s25600 r8192 d23552 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 239540
[    0.000000] Kernel command line: 8250.nr_uarts=0 bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  dwc_otg.lpm_enable=0 console=ttyS0,115200 console=tty1 root=PARTUUID=5fb0d7cb-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 936296K/966656K available (7168K kernel code, 484K rwdata, 2012K rodata, 1024K init, 778K bss, 22168K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xbb800000 - 0xff800000   (1088 MB)
    lowmem  : 0x80000000 - 0xbb000000   ( 944 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .text : 0x80008000 - 0x80800000   (8160 kB)
      .init : 0x80b00000 - 0x80c00000   (1024 kB)
      .data : 0x80c00000 - 0x80c79014   ( 485 kB)
       .bss : 0x80c7b000 - 0x80d3da64   ( 779 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000008] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000025] Switching to timer-based delay loop, resolution 52ns
[    0.000333] Console: colour dummy device 80x30
[    0.001226] console [tty1] enabled
[    0.001275] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.001345] pid_max: default: 32768 minimum: 301
[    0.001703] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001745] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002777] Disabling cpuset control group subsystem
[    0.002968] CPU: Testing write buffer coherency: ok
[    0.003038] ftrace: allocating 22390 entries in 66 pages
[    0.054351] CPU0: update cpu_capacity 1024
[    0.054421] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.054520] Setting up static identity map for 0x100000 - 0x100034
[    0.056755] CPU1: update cpu_capacity 1024
[    0.056763] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.057477] CPU2: update cpu_capacity 1024
[    0.057484] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.058153] CPU3: update cpu_capacity 1024
[    0.058160] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.058243] Brought up 4 CPUs
[    0.058414] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.058444] CPU: All CPU(s) started in HYP mode.
[    0.058470] CPU: Virtualization extensions available.
[    0.059293] devtmpfs: initialized
[    0.070355] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[    0.070678] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.070740] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.071302] pinctrl core: initialized pinctrl subsystem
[    0.072222] NET: Registered protocol family 16
[    0.074507] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.083386] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.083434] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.083613] Serial: AMBA PL011 UART driver
[    0.085510] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.086057] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[    0.154958] bcm2835-dma 3f007000.dma: DMA legacy API manager at bb80f000, dmachans=0x1
[    0.156823] SCSI subsystem initialized
[    0.157004] usbcore: registered new interface driver usbfs
[    0.157106] usbcore: registered new interface driver hub
[    0.157221] usbcore: registered new device driver usb
[    0.163892] raspberrypi-firmware soc:firmware: Attached to firmware from 2017-07-03 14:16
[    0.165321] clocksource: Switched to clocksource arch_sys_counter
[    0.212222] VFS: Disk quotas dquot_6.6.0
[    0.212333] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.212555] FS-Cache: Loaded
[    0.212826] CacheFiles: Loaded
[    0.225100] NET: Registered protocol family 2
[    0.226037] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.226175] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.226385] TCP: Hash tables configured (established 8192 bind 8192)
[    0.226498] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.226565] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.226800] NET: Registered protocol family 1
[    0.227233] RPC: Registered named UNIX socket transport module.
[    0.227266] RPC: Registered udp transport module.
[    0.227293] RPC: Registered tcp transport module.
[    0.227321] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.228290] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    0.230598] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    0.246727] FS-Cache: Netfs 'nfs' registered for caching
[    0.247726] NFS: Registering the id_resolver key type
[    0.247794] Key type id_resolver registered
[    0.247822] Key type id_legacy registered
[    0.250267] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.250413] io scheduler noop registered
[    0.250444] io scheduler deadline registered (default)
[    0.250770] io scheduler cfq registered
[    0.256438] BCM2708FB: allocated DMA memory fa910000
[    0.256494] BCM2708FB: allocated DMA channel 0 @ bb80f000
[    0.306744] Console: switching to colour frame buffer device 228x61
[    0.337355] bcm2835-rng 3f104000.rng: hwrng registered
[    0.337608] vc-cma: Videocore CMA driver
[    0.337725] vc-cma: vc_cma_base      = 0x00000000
[    0.337858] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    0.338008] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    0.338362] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
[    0.354150] brd: module loaded
[    0.363331] loop: module loaded
[    0.363466] Loading iSCSI transport class v2.0-870.
[    0.364190] usbcore: registered new interface driver smsc95xx
[    0.364374] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.592597] Core Release: 2.80a
[    0.592703] Setting default values for core params
[    0.592875] Finished setting default values for core params
[    0.793423] Using Buffer DMA mode
[    0.793530] Periodic Transfer Interrupt Enhancement - disabled
[    0.793697] Multiprocessor Interrupt Enhancement - disabled
[    0.793860] OTG VER PARAM: 0, OTG VER FLAG: 0
[    0.793993] Dedicated Tx FIFOs mode
[    0.794475] WARN::dwc_otg_hcd_init:1032: FIQ DMA bounce buffers: virt = 0xba904000 dma = 0xfa904000 len=9024
[    0.794772] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[    0.795396] dwc_otg: Microframe scheduler enabled
[    0.795446] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x8058ef90
[    0.802290] WARN::hcd_init_fiq:460: FIQ ASM at 0x8058f300 length 36
[    0.808995] WARN::hcd_init_fiq:486: MPHI regs_base at 0xbb87a000
[    0.815747] dwc_otg 3f980000.usb: DWC OTG Controller
[    0.822476] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    0.829353] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
[    0.836156] Init: Port Power? op_state=1
[    0.842772] Init: Power Port (0)
[    0.849594] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.856259] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.862965] usb usb1: Product: DWC OTG Controller
[    0.869611] usb usb1: Manufacturer: Linux 4.9.35-v7+ dwc_otg_hcd
[    0.876256] usb usb1: SerialNumber: 3f980000.usb
[    0.883778] hub 1-0:1.0: USB hub found
[    0.890495] hub 1-0:1.0: 1 port detected
[    0.897846] dwc_otg: FIQ enabled
[    0.897851] dwc_otg: NAK holdoff enabled
[    0.897855] dwc_otg: FIQ split-transaction FSM enabled
[    0.897869] Module dwc_common_port init
[    0.898150] usbcore: registered new interface driver usb-storage
[    0.905009] mousedev: PS/2 mouse device common for all mice
[    0.912739] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[    0.919699] bcm2835-cpufreq: min=600000 max=1200000
[    0.926671] sdhci: Secure Digital Host Controller Interface driver
[    0.933344] sdhci: Copyright(c) Pierre Ossman
[    0.940226] sdhost-bcm2835 3f202000.sdhost: could not get clk, deferring probe
[    0.949245] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[    0.956091] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.965511] ledtrig-cpu: registered to indicate activity on CPUs
[    0.972443] hidraw: raw HID events driver (C) Jiri Kosina
[    0.979502] usbcore: registered new interface driver usbhid
[    0.986387] usbhid: USB HID core driver
[    0.994014] vchiq: vchiq_init_state: slot_zero = 0xba980000, is_master = 0
[    1.002907] Initializing XFRM netlink socket
[    1.010015] NET: Registered protocol family 17
[    1.017089] Key type dns_resolver registered
[    1.024324] Registering SWP/SWPB emulation handler
[    1.032078] registered taskstats version 1
[    1.039354] vc-sm: Videocore shared memory driver
[    1.046443] [vc_sm_connected_init]: start
[    1.053858] [vc_sm_connected_init]: end - returning 0
[    1.066857] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[    1.075637] sdhost: log_buf @ ba907000 (fa907000)
[    1.115456] Indeed it is in host mode hprt0 = 00021501
[    1.205351] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    1.209996] random: fast init done
[    1.221677] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    1.228811] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[    1.295482] of_cfs_init
[    1.302649] of_cfs_init: OK
[    1.305739] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.307768] mmc0: new high speed SDHC card at address b368
[    1.308488] mmcblk0: mmc0:b368 NCard 3.70 GiB
[    1.310965]  mmcblk0: p1 p2
[    1.314237] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.315794] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.317348] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.320133] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.325363] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.325528] Indeed it is in host mode hprt0 = 00001101
[    1.400457] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.407409] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.429733] devtmpfs: mounted
[    1.438397] Freeing unused kernel memory: 1024K (80b00000 - 80c00000)
[    1.471726] mmc1: new high speed SDIO card at address 0001
[    1.555683] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    1.562817] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.570792] hub 1-1:1.0: USB hub found
[    1.578135] hub 1-1:1.0: 5 ports detected
[    1.905375] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    2.009274] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[    2.017206] systemd[1]: Detected architecture 'arm'.
[    2.045749] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    2.045758] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.054621] smsc95xx v1.0.5
[    2.159055] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:73:d2:fa
[    2.265575] usb 1-1.4: new high-speed USB device number 4 using dwc_otg
[    2.288295] NET: Registered protocol family 10
[    2.297628] systemd[1]: Inserted module 'ipv6'
[    2.307490] systemd[1]: Set hostname to <raspberrypi>.
[    2.315219] systemd[1]: Initializing machine ID from random generator.
[    2.323131] systemd[1]: Installed transient /etc/machine-id file.
[    2.415764] usb 1-1.4: New USB device found, idVendor=0409, idProduct=005a
[    2.423603] usb 1-1.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.436379] hub 1-1.4:1.0: USB hub found
[    2.445645] hub 1-1.4:1.0: 4 ports detected
[    2.545389] usb 1-1.5: new high-speed USB device number 5 using dwc_otg
[    2.676163] usb 1-1.5: New USB device found, idVendor=2040, idProduct=0264
[    2.683809] usb 1-1.5: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[    2.691352] usb 1-1.5: Product: soloHD
[    2.698942] usb 1-1.5: Manufacturer: HCW
[    2.706369] usb 1-1.5: SerialNumber: 0011549313
[    2.785415] usb 1-1.4.3: new high-speed USB device number 6 using dwc_otg
[    2.916024] usb 1-1.4.3: New USB device found, idVendor=045e, idProduct=02d5
[    2.923584] usb 1-1.4.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.931118] usb 1-1.4.3: Product: Xbox USB Tuner
[    2.938572] usb 1-1.4.3: Manufacturer: Microsoft Corp.
[    2.946064] usb 1-1.4.3: SerialNumber: 000684150615
[    2.974688] systemd[1]: Cannot add dependency job for unit regenerate_ssh_host_keys.service, ignoring: Unit regenerate_ssh_host_keys.service failed to load: No such file or directory.
[    2.983055] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[    2.994258] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[    3.002875] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    3.245390] usb 1-1.4.4: new high-speed USB device number 7 using dwc_otg
[    3.394076] usb 1-1.4.4: New USB device found, idVendor=067b, idProduct=2773
[    3.394100] usb 1-1.4.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.394109] usb 1-1.4.4: Product: ATAPI-6 Bridge Controller
[    3.394123] usb 1-1.4.4: Manufacturer: Prolific Technology Inc.
[    3.394141] usb 1-1.4.4: SerialNumber: 0123456789000000006
[    3.395524] usb-storage 1-1.4.4:1.0: USB Mass Storage device detected
[    3.396409] scsi host0: usb-storage 1-1.4.4:1.0
[    4.038786] systemd-udevd[148]: starting version 215
[    4.408242] scsi 0:0:0:0: Direct-Access     WDC WD10 EADS-11M2B2      80.0 PQ: 0 ANSI: 0
[    4.409918] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[    4.410478] sd 0:0:0:0: [sda] Write Protect is off
[    4.410496] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[    4.410883] sd 0:0:0:0: [sda] No Caching mode page found
[    4.410896] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    4.411407] scsi 0:0:0:1: Direct-Access     WDC WD10 EARS-00Y5B1      80.0 PQ: 0 ANSI: 0
[    4.413447] sd 0:0:0:1: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[    4.436774] sd 0:0:0:1: [sdb] Write Protect is off
[    4.436792] sd 0:0:0:1: [sdb] Mode Sense: 03 00 00 00
[    4.437825] sd 0:0:0:1: [sdb] No Caching mode page found
[    4.437840] sd 0:0:0:1: [sdb] Assuming drive cache: write through
[    4.507548]  sda: sda1 sda2
[    4.517354]  sdb: sdb1 sdb2
[    4.519484] sd 0:0:0:0: [sda] Attached SCSI disk
[    4.520395] sd 0:0:0:1: [sdb] Attached SCSI disk
[    4.743058] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[    4.745430] usb 1-1.4.1: new high-speed USB device number 8 using dwc_otg
[    4.877135] usb 1-1.4.1: New USB device found, idVendor=152d, idProduct=8561
[    4.877153] usb 1-1.4.1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[    4.877161] usb 1-1.4.1: Product: JMS56x Series
[    4.877169] usb 1-1.4.1: Manufacturer: JMicron
[    4.877177] usb 1-1.4.1: SerialNumber: 00A123456877
[    4.878704] usb-storage 1-1.4.1:1.0: USB Mass Storage device detected
[    4.879330] scsi host1: usb-storage 1-1.4.1:1.0
[    4.898115] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    4.898439] sd 0:0:0:1: Attached scsi generic sg1 type 0
[    5.265087] usbcore: registered new interface driver brcmfmac
[    5.386174] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    5.483887] brcmfmac: Firmware version = wl0: May 27 2016 00:13:38 version 7.45.41.26 (r640327) FWID 01-df77e4a7
[    5.667875] random: crng init done
[    5.926294] scsi 1:0:0:0: Direct-Access     SAMSUNG  HN-M101MBB       0107 PQ: 0 ANSI: 6
[    5.927857] sd 1:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[    5.928419] sd 1:0:0:0: [sdc] Write Protect is off
[    5.928435] sd 1:0:0:0: [sdc] Mode Sense: 47 00 10 08
[    5.928940] sd 1:0:0:0: [sdc] No Caching mode page found
[    5.928952] sd 1:0:0:0: [sdc] Assuming drive cache: write through
[    5.945524] sd 1:0:0:0: Attached scsi generic sg2 type 0
[    5.952786]  sdc: sdc1
[    5.953267] scsi 1:0:0:1: Direct-Access     ST350031 2CS              0107 PQ: 0 ANSI: 6
[    5.955134] sd 1:0:0:1: Attached scsi generic sg3 type 0
[    5.956735] sd 1:0:0:1: [sdd] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    5.957526] sd 1:0:0:1: [sdd] Write Protect is off
[    5.957538] sd 1:0:0:1: [sdd] Mode Sense: 47 00 10 08
[    5.958393] sd 1:0:0:1: [sdd] No Caching mode page found
[    5.958405] sd 1:0:0:1: [sdd] Assuming drive cache: write through
[    5.959443] sd 1:0:0:0: [sdc] Attached SCSI disk
[    5.984429]  sdd: sdd1
[    5.995532] sd 1:0:0:1: [sdd] Attached SCSI disk
[    6.054361] media: loading out-of-tree module taints kernel.
[    6.056765] media: Linux media interface: v0.10
[    6.093824] Linux video capture interface: v2.00
[    6.093836] WARNING: You are using an experimental version of the media stack.
    As the driver is backported to an older kernel, it doesn't offer
    enough quality for its usage in production.
    Use it with care.
Latest git patches (needed if you report a bug to [email protected]):
    da48c948c263c9d87dfc64566b3373a858cc8aa2 media: fix warning on v4l2_subdev_call() result interpreted as bool
    14330d7f08bab92029f0c95c70fe200e8d76b31e media: imx: csi: enable double write reduction
    9e6b1dae37810bec45c80d478636b254db377eaa media: coda: explicitly request exclusive reset control
[    6.143631] em28xx 1-1.5:1.0: New device HCW soloHD @ 480 Mbps (2040:0264, interface 0, class 0)
[    6.143650] em28xx 1-1.5:1.0: DVB interface 0 found: isoc
[    6.144246] em28xx 1-1.5:1.0: chip ID is em28178
[    6.202808] systemd-journald[145]: Received request to flush runtime journal from PID 1
[    8.232310] em28xx 1-1.5:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x75ebcd04
[    8.232318] em28xx 1-1.5:1.0: EEPROM info:
[    8.232327] em28xx 1-1.5:1.0:     microcode start address = 0x0004, boot configuration = 0x01
[    8.238882] em28xx 1-1.5:1.0:     AC97 audio (5 sample rates)
[    8.238892] em28xx 1-1.5:1.0:     500mA max power
[    8.238904] em28xx 1-1.5:1.0:     Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
[    8.239147] em28xx 1-1.5:1.0: Identified as PCTV tripleStick (292e) (card=94)
[    8.239160] em28xx 1-1.5:1.0: dvb set to isoc mode.
[    8.239599] usbcore: registered new interface driver em28xx
[    8.265884] WARNING: You are using an experimental version of the media stack.
    As the driver is backported to an older kernel, it doesn't offer
    enough quality for its usage in production.
    Use it with care.
Latest git patches (needed if you report a bug to [email protected]):
    da48c948c263c9d87dfc64566b3373a858cc8aa2 media: fix warning on v4l2_subdev_call() result interpreted as bool
    14330d7f08bab92029f0c95c70fe200e8d76b31e media: imx: csi: enable double write reduction
    9e6b1dae37810bec45c80d478636b254db377eaa media: coda: explicitly request exclusive reset control
[    8.273728] em28xx 1-1.5:1.0: Binding DVB extension
[    8.297876] i2c i2c-4: Added multiplexed i2c bus 5
[    8.297894] si2168 4-0064: Silicon Labs Si2168-B40 successfully identified
[    8.297902] si2168 4-0064: firmware version: B 4.0.2
[    8.312454] si2157 5-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
[    8.312504] dvbdev: DVB: registering new adapter (1-1.5:1.0)
[    8.312521] em28xx 1-1.5:1.0: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
[    8.312540] dvbdev: dvb_create_media_entity: media entity 'Silicon Labs Si2168' registered.
[    8.315039] dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
[    8.319414] em28xx 1-1.5:1.0: DVB extension successfully initialized
[    8.319438] em28xx: Registered (Em28xx dvb Extension) extension
[    8.336693] WARNING: You are using an experimental version of the media stack.
    As the driver is backported to an older kernel, it doesn't offer
    enough quality for its usage in production.
    Use it with care.
Latest git patches (needed if you report a bug to [email protected]):
    da48c948c263c9d87dfc64566b3373a858cc8aa2 media: fix warning on v4l2_subdev_call() result interpreted as bool
    14330d7f08bab92029f0c95c70fe200e8d76b31e media: imx: csi: enable double write reduction
    9e6b1dae37810bec45c80d478636b254db377eaa media: coda: explicitly request exclusive reset control
[    8.341120] em28xx 1-1.5:1.0: Registering input extension
[    8.385348] Registered IR keymap rc-pinnacle-pctv-hd
[    8.385752] rc rc0: 1-1.5:1.0 IR as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/rc/rc0
[    8.385931] input: 1-1.5:1.0 IR as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/rc/rc0/input0
[    8.385958] em28xx 1-1.5:1.0: Input extension successfully initialized
[    8.385962] em28xx: Registered (Em28xx Input Extension) extension
[    8.543084] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[    8.543101] brcmfmac: power management disabled
[    9.379728] uart-pl011 3f201000.serial: no DMA platform data
[   10.736478] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   11.173720] Adding 102396k swap on /var/swap.  Priority:-1 extents:4 across:241660k SSFS
[   12.356637] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
[   14.378952] Bluetooth: Core ver 2.22
[   14.379002] NET: Registered protocol family 31
[   14.379006] Bluetooth: HCI device and connection manager initialized
[   14.379020] Bluetooth: HCI socket layer initialized
[   14.379028] Bluetooth: L2CAP socket layer initialized
[   14.379065] Bluetooth: SCO socket layer initialized
[   14.389824] Bluetooth: HCI UART driver ver 2.3
[   14.389831] Bluetooth: HCI UART protocol H4 registered
[   14.389834] Bluetooth: HCI UART protocol Three-wire (H5) registered
[   14.389937] Bluetooth: HCI UART protocol Broadcom registered
[   14.653396] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.653406] Bluetooth: BNEP filters: protocol multicast
[   14.653424] Bluetooth: BNEP socket layer initialized
[   15.292846] si2168 4-0064: Direct firmware load for dvb-demod-si2168-b40-01.fw failed with error -2
[   15.298490] si2168 4-0064: please install firmware file 'dvb-demod-si2168-b40-01.fw'
[   15.298496] si2168 4-0064: downloading firmware from file 'dvb-demod-si2168-02.fw'
[   15.298502] si2168 4-0064: firmware download failed -22
[   15.302956] si2157 5-0060: found a 'Silicon Labs Si2157-A30'

maybe that help...

RE: Xbox One DVB-T/T2/C tuner - Added by Andras Farago over 7 years ago

Olli Salonen wrote:

Thanks CvH, I was planning to, but now I don't have to. Will you compile it for x86 as well please? :)

Andras, ok, there's not much we can do then, except start to guess which registers to change but that's a neverending task. I'll do that power level thing a bit later, the next couple of weeks I'm very little in front of my PC...

I have another plan. One of my colleague has an Xbox one, I have a tuner and a i2c sniffer, so next week I am going to sniff the i2c communication between the demodulator ic and the tuner with an Xbox. I tried it, the method is working with the linux driver, I can see what control datas the tuner get, so the next step is the same but with an Xbox.

RE: Xbox One DVB-T/T2/C tuner - Added by Stephen Neal over 7 years ago

marco raap wrote:

Smith Martin Neal

did all you said and after 4 hours. Didn't work. Nice try.

So my last hope depends on C vH and his Image.
Sad why is it not possible to just use the driver.....

[...]

[...]

maybe that help...

Did you definitely install the kernel headers on a fresh Jessie Lite install?

RE: Xbox One DVB-T/T2/C tuner - Added by C vH over 7 years ago

Stephen Neal wrote:

Did you definitely install the kernel headers on a fresh Jessie Lite install?

maybe make install is missing, his log shows some different media_build version

#install base system
sudo apt update && sudo apt upgrade
sudo apt install raspberrypi-kernel-headers make gcc git patch patchutils libproc-processtable-perl

#clone git
cd
git clone git://linuxtv.org/media_build.git
git clone --depth=1 https://github.com/trsqr/media_tree.git -b xboxone ./media

#build media_build
cd media_build
make dir DIR=../media
make distclean
make

#install it
sudo make install

#download the needed fws
cd /lib/firmware
sudo wget http://linuxtv.org/downloads/firmware/dvb-usb-dib0700-1.20.fw
sudo wget http://palosaari.fi/linux/v4l-dvb/firmware/MN88472/02/latest/dvb-demod-mn88472-02.fw

reboot

that worked for me at a fresh new raspbian (iirc)

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

ok. i´ll give it a try later

RE: Xbox One DVB-T/T2/C tuner - Added by Anonymous over 7 years ago

Btw guys, even if it's obvious, there are 2 types of Xbox One USB Tuners.

- Haupauge DVB-S ATSC for the US region
- NXP DVB-T/DVB-T2/DVB-C

Just making sure you all know :P

RE: Xbox One DVB-T/T2/C tuner - Added by Stephen Neal over 7 years ago

Tux User wrote:

Btw guys, even if it's obvious, there are 2 types of Xbox One USB Tuners.

- Haupauge DVB-S for the US region
- NXP DVB-T/DVB-T2/DVB-C

Just making sure you all know :P

Yep - this thread is purely for the DVB-T/T2/C one (as per thread title)

But surely the US XBox One tuner is ATSC 8VSB (i.e. the US OTA Digital Terrestrial standard) not DVB-S (the satellite standard)?

RE: Xbox One DVB-T/T2/C tuner - Added by Anonymous over 7 years ago

Thanks Stephen, you are right, corrected

RE: Xbox One DVB-T/T2/C tuner - Added by C vH over 7 years ago

marco raap wrote:

ok. i´ll give it a try later

RPi2/3 image http://cvh.libreelec.tv/Test/xbox/

LibreELEC-RPi2.arm-8.1-xbox-dvb-driver-mb-1.2.img.gz

looks now working for me :)

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

C vH wrote:

marco raap wrote:

ok. i´ll give it a try later

RPi2/3 image http://cvh.libreelec.tv/Test/xbox/

LibreELEC-RPi2.arm-8.1-xbox-dvb-driver-mb-1.2.img.gz

looks now working for me :)

ok. now I´ve started the compiling. takes 2 hours. Why do I habe to compile all the drivers? Who cares. I can tell you later if your Images Worked for me.

RE: Xbox One DVB-T/T2/C tuner - Added by Olli Salonen over 7 years ago

Andras Farago wrote:

I have another plan. One of my colleague has an Xbox one, I have a tuner and a i2c sniffer, so next week I am going to sniff the i2c communication between the demodulator ic and the tuner with an Xbox. I tried it, the method is working with the linux driver, I can see what control datas the tuner get, so the next step is the same but with an Xbox.

@Andras

That sounds great! Will be interesting to compare the problematic frequencies. First question of course is, will you be able to watch all the channels problem-free using the Xbox itself? Then if yes, we should focus on the I2C communication.

RE: Xbox One DVB-T/T2/C tuner - Added by Walter av over 7 years ago

Smith Martin Neal

Compiling and testing DVB-T on rpi3 succeeded on kernel 4.9.40-v7+, however I used a updated kernel (rpi-update and possible a bad usb media) in the first place that might break things. To let it compile with a updated kernel I had to add extra packages to fix the updated kernel sources/headers which needs to be added manually by rpi-source:

#update base image
sudo apt update && sudo apt upgrade
sudo apt install raspberrypi-kernel-headers make gcc git patch patchutils libproc-processtable-perl firmware-linux-nonfree bc libncurses5-dev libdigest-sha-perl

#incase of upgrading the kernel 4.9.40-v7+!!!
sudo apt update && sudo apt dist-upgrade
sudo rpi-update
sudo wget https://raw.githubusercontent.com/notro/rpi-source/master/rpi-source -O /usr/bin/rpi-source && sudo chmod +x /usr/bin/rpi-source && /usr/bin/rpi-source -q --tag-update
rpi-source #this will get modified+ kernel sources and headers
sudo reboot

#!!!make sure you are currently running the kernel as you would like to build these modules for, otherwise reboot first!!!

#clone media_build and patched xbox sources
mkdir -p xboxtuner/attempt01
cd xboxtuner/attempt01
git clone git://linuxtv.org/media_build.git
git clone --depth=1 https://github.com/trsqr/media_tree.git -b xboxone ./media

#reset&build media_build
cd media_build
git reset --hard 258461908cbb83a4d2f869f0f70b6b511fce6baa #since 2017-08-08 commits break building V4L2/LINUX
make dir DIR=../media
make distclean
cp ../media/mm/frame_vector.c v4l/ #otherwise building will fail on this!
make -j4 #adding -j4 will make use of the quadcore in the rpi2/3 and decrease build time! 

#force install build kernel modules
sudo make install

#download the needed firmware
cd /lib/firmware
#dib0700 firmware is packaged in "firmware-linux-nonfree" 
sudo wget http://palosaari.fi/linux/v4l-dvb/firmware/MN88472/02/latest/dvb-demod-mn88472-02.fw

#install tvheadend
sudo apt-key adv --keyserver hkp://keyserver.ubuntu.com:80 --recv-keys 379CE192D401AB61
echo "deb https://dl.bintray.com/tvheadend/deb raspbianjessie stable-4.2" | sudo tee -a /etc/apt/sources.list
sudo apt-get update
sudo apt-get install tvheadend

#if the tuner isn't working yet by just inserting its USB plug than...
sudo reboot;exit

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

C vH wrote:

Stephen Neal wrote:

Did you definitely install the kernel headers on a fresh Jessie Lite install?

maybe make install is missing, his log shows some different media_build version

#install base system
sudo apt update && sudo apt upgrade
sudo apt install raspberrypi-kernel-headers make gcc git patch patchutils libproc-processtable-perl

#clone git
cd
git clone git://linuxtv.org/media_build.git
git clone --depth=1 https://github.com/trsqr/media_tree.git -b xboxone ./media

#build media_build
cd media_build
make dir DIR=../media
make distclean
make

#install it
sudo make install

#download the needed fws
cd /lib/firmware
sudo wget http://linuxtv.org/downloads/firmware/dvb-usb-dib0700-1.20.fw
sudo wget http://palosaari.fi/linux/v4l-dvb/firmware/MN88472/02/latest/dvb-demod-mn88472-02.fw

reboot

that worked for me at a fresh new raspbian (iirc)

I did exactly this. and yeah it worked. First step done to my headless tv server.
Next I´ll try your Image until I get a new raspberry.

RE: Xbox One DVB-T/T2/C tuner - Added by Stephen Neal over 7 years ago

C vH wrote:

marco raap wrote:

ok. i´ll give it a try later

RPi2/3 image http://cvh.libreelec.tv/Test/xbox/

LibreELEC-RPi2.arm-8.1-xbox-dvb-driver-mb-1.2.img.gz

looks now working for me :)

Working for me in the UK from Crystal Palace - all 9 muxes working fine. (6 x DVB-T and 3 x DVB-T2)

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

@ C vH

Your Image works now. I Find Services Great work. Thank You for the work.

RE: Xbox One DVB-T/T2/C tuner - Added by Anthony Thomas over 7 years ago

After a little while of testing a 4x XBox One tuner DVB-C setup I have noticed that there are definitely some signal issues with this tuner.

They don't perform anywhere near as well as an Astrometa MN88473 based tuner. Regular pixelisation.

I've tried adding a powered amplifier but I know if you're boosting a poor signal it often makes it worse, but I also don't think it's a poor signal in the first place (or certainly not too bad).

I also saw yesterday when TVH tried to do an epggrab on 3 tuners, whilst I was watching TV through another, the signal went through the floor with many errors. But strangely only on one mux - muxes either side were as before, very odd.

Maybe I need a better quality signal splitter, or to change how I route the cable to the tuners - currently using some screw on gender changers which I know aren't too great.

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

After testing the Image from C vH I must say it is the beste Libreelec that I ever use.
It all worked so fine both tuners work great and can record one channel and watch another. Never experience this. Now we need PiP in Kodi :)
i´m very pleased.

RE: Xbox One DVB-T/T2/C tuner - Added by Mark Clarkstone over 7 years ago

Anthony Thomas wrote:

After a little while of testing a 4x XBox One tuner DVB-C setup I have noticed that there are definitely some signal issues with this tuner.

They don't perform anywhere near as well as an Astrometa MN88473 based tuner. Regular pixelisation.

I've tried adding a powered amplifier but I know if you're boosting a poor signal it often makes it worse, but I also don't think it's a poor signal in the first place (or certainly not too bad).

I also saw yesterday when TVH tried to do an epggrab on 3 tuners, whilst I was watching TV through another, the signal went through the floor with many errors. But strangely only on one mux - muxes either side were as before, very odd.

Maybe I need a better quality signal splitter, or to change how I route the cable to the tuners - currently using some screw on gender changers which I know aren't too great.

I have the original Astrometa (MN88472) and experienced the same problem on DVB-T again with only one mux - the strongest one of all. Now here's the interesting thing, both xbox tuners are connected to the same powered splitter using quality cables (with another 4+ tuners, all fine). The one (xbox tuner, using a cable that was made) is fine, the other with a high quality (sealed) cable glitched like hell, I switched it out with a cheapo poundland cable, and guess what, it's fine!

Make of that what you will.. (yes, I checked the cables were all connected correctly many times).

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

@C vH

how can I compile my own LibreELEC build with additional software?
I have a Mac
i have VirtualBox and Ubuntu Server.

But I can't find a tutorial on how to change the Software

RE: Xbox One DVB-T/T2/C tuner - Added by C vH over 7 years ago

marco raap wrote:

But I can't find a tutorial on how to change the Software

https://wiki.libreelec.tv/index.php?title=Compile

It is pretty easy AFTER you understood how it works, before it is not that easy ;)

RE: Xbox One DVB-T/T2/C tuner - Added by marco raap over 7 years ago

ERROR: Architecture not found, use a valid Architecture
for your project or create a new config

I get this error after doing it step by step so something I am missing?

(126-150/420)