Tvheadend

And now additionally the dropdown box for "pre-defined" muxes is empty and stays empty - also after page reload, and even after reboot. wtf?

fyi: new Ticket https://tvheadend.org/issues/2188

1. choose an adapter
2. setup the two satellite configurations
3. add dvb network by location for both satellite configurations - make sure to add the config for the selected network
4. let tvheadend find the muxes
5. map dvb services to channels

That worked for me.

Hey there,

but you don't use unicable, if I am correct?

3.4 is not working with unicable as far as I have in mind.

Best

Right, unicable support ist still broken :(
But you can try seifes fork (based on 3.5) which works perfectly with unicable https://github.com/seife/tvheadend

With the current github build unicable should work. They fixed a config parser issue in the last days.
If not, see my ticket above - there's a patch added.

If you have questions do not hesitate to ask.

Concerning seife's build: I couldn't compile it under Ubuntu 14.04 (ffmpg issue as I read later) so that I just waited on this bugfix.
All my unicable problems have been fixed.

Best
Kai

Hi Kai,
it had also a ticket open https://tvheadend.org/issues/1937
But it doesnt work for me.
Scan gets only data from some transponders, changes in SCR# or freq doesnt affect anything.

confused....

Hi,

well at least the bug that your adapter can not get opened after restart, should be fixed.
I had no problems while searching channels... ok perhaps 5 muxes failed, but I can use all programs I need.

Here the steps to update your github build in the right way. I don't know if you're familiar with this - just want to be sure:

stop tvheadend

cd <your tvheadend github folder>
git pull
./configure
make clean
make distclean
make
and perhaps make install - if you did this also before.

start tvheadend
configure your adapter(s)

delete all muxes/services/programs

trigger a new scan.

When finished, restart tvheadend and I hope you can see then that the adapter(s) can be opened in the right way.
The steps "make clean" and "make distclean" are optional, but they may resolve also some issues (I often stumble over these steps while reading threads) - so give them also a try.

Best
Kai

Yeah the adapter bug has gone, try it from scratch now.

Same sh*t:

mpegts: 11332.25H in Bumbes - scan no data, failed

Transponder 11332.25H is party of Skys Program :-|

well ok, i cannot help you with the failed scans. My target was to help you with the adapter problem

Thx anyway

Hi Matthias,

are your problems still there?
Can try https://github.com/InuSasha/tvheadend/tree/fixes/bug2229-en50494?

Please, do the scan with no other device activ, except the devices in TVH.

Thanks,
Sascha

PS: https://tvheadend.org/issues/2229

Thx,ill try it when im at home, on vacation right now

No effect, still doesnt find all services.
Just french, spain, only some german (sat1,rtl,rtl2) channels.

Hi Matthias,

that are bad news.
Can you give us some debug/trace logs?
Without, we will have no chance to fix your problem.

regards,
Sascha

Sure, running a new scan from a 'fresh' installation.
Debug log attached...until tvheadend crashed

Some strange entries:
2014-09-03 14:14:50.244 [ DEBUG]:mpegts: 11739V in astra - no free tuner available
2014-09-03 14:14:50.245 [ DEBUG]:mpegts: 10891.25H in astra - no free tuner available

??

no free adapter just means that all of your adapters are busy. the reason may be a misconfiguration - or they are busy ;)
If you have two adapters with the same name (like I had) rename them and this makes your life a bit easier while searching problems.
e.g.Conexant CX24116/CX24118 : DVB-S #0 and Conexant CX24116/CX24118 : DVB-S #1.

I also had this error message and the reason was a misconfiguration (ok, the reason was the bug in the config-parser module in my case).

Best Kai

Well, i have just one adapter,and if its busy while scanning,the error makes sense

The Log is a bit confusing. It looks like, the adapter begin to scan an other mux, but the last scan is not completed.
Did you mean with "fresh installation" a delete configuration?

I don't know where the bug is. May be not en50494, but i am not sure.

2014-09-03 14:08:39.039 [ DEBUG]:mpegts: 12480V in astra - close PID 0BBB (3003)
2014-09-03 14:08:39.198 [ INFO]:mpegts: 12031.5H in astra - tuning on Conexant CX24116/CX24118 : DVB-S #0
2014-09-03 14:08:40.135 [ DEBUG]:en50494: lnb=0 id=0 freq=1210 pin=256 v/h=1 l/u=1 f=1431500, data=0x0D36
2014-09-03 14:08:40.595 [ DEBUG]:linuxdvb: Conexant CX24116/CX24118 : DVB-S #0 - starting 12031.5H in astra
2014-09-03 14:08:40.602 [ DEBUG]:mpegts: 12031.5H in astra - started
2014-09-03 14:08:40.619 [ INFO]:subscription: 'scan' subscribing to mux, weight: 4, adapter: 'Conexant CX24116/CX24118 : DVB-S #0', network: 'astra', mux: '12031.5H', hostname: '<N/A>', username: '<N/A>', client: '<N/A>'
2014-09-03 14:08:40.620 [ DEBUG]:mpegts: 12460.5H in astra - no free tuner available
2014-09-03 14:08:40.621 [ DEBUG]:mpegts: 12480V in astra - no free tuner available

Maybe im doing something wrong while configuring the adapter?
But i did the same on seifes fork.

1. change satconfig to unicable
2. change scr id and freq to my settings
3. add a network (astra 19.2)
4. add this network to the unicable switch
5. enable the adapter

then...scanning starts...and fails on most muxes.
my lnb is a wisi oc05c http://katalog.wisi.de/index.php?IdTreeGroup=133&IdProduct=1146

ps: yes,new installation,old configs deleted

the problem is, the dvb-code was completely rewritten.
i can not say, is the problem in the uni-cable or the new dvb-code.

Had you test tvh with the legacy-port of the lnb?

Schönen Abend noch,
Sascha

Mh, no, i can test it tomorrow maybe.
But, as i mentioned before (i think ) seifes port is running without any problems.

Dir auch einen schönen Abend

Ok,sorry,im tired.
it works on the legacy port,was a cable problem.

Hi Matthias,

a cable-problem? so the unicable works now, too?

Sascha